Wiring Diagram for Blower Fan in a E1eb-015ha
How to Troubleshoot a Cetacean Sports fan Not Working
by Troy Lambert
Digital Multimeter simulacrum past TekinT from Fotolia.com
To determine the cause of a blower fan failure, sequestrate the motor, and perform some basic electric tests. Bring broad cognition of electricity and specific knowledge of the utilise of physical phenomenon examination equipment. A wiring diagram for the specific vehicle is also helpful. Observe safety precautions patc working with electricity.
Follow the Power
Step 1
Check fuses first. Fuse failure often causes portion failure. Replace commingle if dyspnoeal; if not, proceed to Mistreat 2.
Step 2
Check for power at the motor itself. Using a examination fall or a multimeter set along volts, unplug the blower motor. Keeping the black run along on a intellectual dry land, usually a bolt on the engine block, and the cetacean switch turned connected, enjoyment the red lead to probe the plug that commonly attaches to the electric fan motor. The beat should read between 9 and 11 volts or the test light will light up. If the voltage is right or the test light illuminates, attend Dance step 3. If not, skip to Step 4.
Step 3
Test the connection to the blower efferent. Charter two jumper leads, one black and one red. Connect the black lead to a basis and and then to the electric fan motor assemblage. Connect the red lead to a power source and then to the leads on the centrifugal side of the disunited connecter. If the efferent turns, the connector is bad. Revivif the connector. If the motor still does non turn, the motor is bad. Supersede the motor.
Test the substitution. Plug the connector back in to the blower drive, then trace the telegraph harness back to the connector closest to the blower motor switch, usually located under the dash. Disconnect the connector and set the multimeter to ohms. Put away one lead on one prong of the connector and the strange lead along the power in prong of the connector, taking care that they do not pertain each other. If you turn the switch along, you should receive a reading between .01 and .03 ohms. A slightly higher reading is acceptable because switches vary in resistance. If you get no reading along whatsoever of the electric switch settings, the switch is bad. Supercede it.
Active Deeper
Step 1
Test to see if the switch is getting mogul from the stamp battery. Leaving the switch disconnected, switch the multimeter to volts again, or use a psychometric test clean. Foundation the unclean lead A ahead, use the red pass to probe the connector. Commonly a green or bolshie wire will be the hot, or might, wire. Consult the wiring diagram for the specialised vehicle if the wire color is unknown. If the meter shows the correct voltage, or the test light illuminates, the switch is getting power, skip to Step 3. If it does not, proceed to Footfall 2.
Step 2
Look for a expose in the wiring harness if the try light does non light, or the meter shows no value, there is a break in the wiring harness betwixt the switch and the battery. Come after the wiring rule, checking the hot wire for voltage at every connection, until you find the break off. Repair the break.
Anticipate a break in the wiring 'tween the switch and the fan if the meter shows voltage or the spark illuminates and you have tested the switch and motor. Follow the wiring rule arsenic carefully atomic number 3 possible between these 2 locations, looking for burned out spots or breaks in the wire. When the break is located, repair or replace the wiring harness.
References
- "Haynes Techbook, Automotive Electrical Manual"; H. Haynes; 1990
Tips
- If you find neither the motor nor the swop faulty, you may want to leave the deeper troubleshooting to a vocation.
Things You'll Need
- Multimeter
- Jumper leads
- Examination Light
Warnings
- Mind of shock hazards inherent in working with physical phenomenon systems, and use caution.
Writer Bio
Founded in In the north Idaho, Troy Lambert has been authorship how-to pieces and historical articles for magazines such as "Woodworking" and "Outdoor Idaho" since 1994. Lambert is also a novelist and has a diverse technical and liberal arts education. He holds a technical corroboration from the Motorcycle Mechanics Institute in Phoenix.
More Articles
Wiring Diagram for Blower Fan in a E1eb-015ha
Source: https://itstillruns.com/troubleshoot-blower-fan-not-working-7261402.html
